Find Your Unique Tail Table Setup!

-
Loosen the dial on the clip mechanism. Insert it into the Tail Table tray slot, and then attach the clip onto your vehicles U-latch.
-
Pop out the Swinging Legs. Note; if your bumper is too low for either the Swinging Legs or Static Legs to reach, you may need longer legs and a longer clip mechanism. You can have request to receive leg extensions and/or a longer clip mechanism at team@spaceinnovationlabs.com. Rare SUVs and some Vans tend to have lower sitting bumpers which require extensions. We will priority ship them to you at no cost if they weren't included with your order.
-
Unscrew the Metal Legs (with rubber feet) so they extend a few inches from the swinging legs. It's best to have all three legals touching the vehicle.
i. Note; if your bumper sits very close to your U-latch so that the Swinging Legs are too far out from your bumper to brace effectively, remove the metal legs and instert them into the Static Leg Holes just behind the Swinging Legs.
ii. Note; if your bumper is too low for either the Swinging Legs or Static Legs to reach, you should have or request to receive leg extensions at team@spaceinnovationlabs.com. Rare SUVs and some Vans tend to have lower sitting bumpers which require extensions. We will priority ship them to you at no cost if they weren't included with your order.
-
Rotate The Latch Dial To Secure Connection: By simply turning the dial a few rotations you effectively tighten the Tail Table Unit to your vehicle. For optimal stability, have your unit titled slightly up and give the dial a few extra twists.
-
Releasing The Latch: To release, you much first loosen the dial 2-3 full turns before pulling the release cord. Dial can be stored inside the tray along with the chopping board so it's not bouncing around in your Tail Table bag.
Now, you are all set! For daily use, setting up the Tail Table is as simple as ‘Clip, Brace, Dial Down, Level, Insert Chopping Board, and Enjoy!’
-
Clip; Push the clip down onto your vehicles U latch until you hear a click. Pull up to ensure it is secure. Dial it down once all 3 feet are securely in contact with your bumper and interior floor of your vehicle.
-
Brace; Brace the feet against your bumper.
-
Dial it down; Dial down the Tail Table’s Hook and Dail system tightly to the U-latch. We find that it’s helps to push down on the handle while dialing down to get it super tight! Don’t worry, you won’t hurt it, or your U-latch. Give it a good extra twist!
-
Level; The great thing about a Tail Table is you do not need flat ground. Anywhere you park you will be able to twist the metal legs to get a level surface. Reach under the table, and even push the table up from the bottom if needed to get the legs to turn freely for adjustments.
-
Insert Chopping Board; Connect the two sides of the chopping board (like a LEGO). Then insert the chopping board into the handle. Then close the table to make the full LEGO-like connection.
-
Enjoy!!! The best part of the Tail Table is that in less than 60 seconds you can have the ultimate home away from home.
Try The 4 Different
Tail Table Configurations

Care & Maintenance
-
Do not set more than 25lbs on the outer edges of the Tail Table. The Tail Table is intended for light duty use such as eating and drinking. Storing large items on the Tail Table is not recommended.
-
The silicon mats and chopping board are food safe material. A light rinsing or soap and water is all that's needed to clean these surfaces. The silicon mats are dishwasher safe!
-
The Tail Table was engineered to last a lifetime of fun in the sun. All metal parts are stainless steel and the rest is high grade ABS plastic. If you drop the unit in salt water feel free to give it a rinse off in clean water and it will be just fine!